Showing posts with label tips. Show all posts
Showing posts with label tips. Show all posts

Friday, August 5, 2011

Monitor power consumption basics

Monitor power consumption basics
Raise your hand if you're interested in saving a few extra dollars. That's what we thought. Do you want to save the planet, too? Buying the right monitor can not fix the world, but paying attention to energy consumption when you buy to help make the world a better place while saving a few pennies. In these pages will explain why the consumption of energy is important, what you can do to conserve power, as different monitors stack up against each other to power conservation, and how CNET tests monitor energy consumption.


Conserving energy can save you money
25The less energy your monitor stepping, lower your monthly electricity bill. How much lower? It depends on two key factors. The first is how often you use your monitor does not have to sit in front of it, surf the Internet, games or editing spreadsheets, just how often your monitor is turned on and displays the image. The second factor determining how much you will save the brightness setting on your monitor, which controls the intensity of lighting your desk. The lower you set your light, the less power you use.
You can not save the world just by turning off your monitor when you leave the house, but you're not helping matters of leaving, either. By conserving the amount of energy you use, you can reduce demand for fossil fuels like coal, oil and natural gas. Less burning of fossil fuels means lower emissions of carbon dioxide, the primary contribution to global warming. It's as simple as that. And then, of course, there's the money-saving perk. More.


How can I save my energy monitor?
Sleep mode is your friend
Make sure when you are in front of your monitor, the device is resting up. You can set the sleep mode in Windows by going to Control Panel and choosing the Power Options. Select the Power Schemes tab and under involved, change the "Turn off monitor" field to whatever time suits you. (We recommend at least 5 minutes to avoid approve your monitor off while reading a long article.)


Turn down your light
Light is one of the most important attributes to determine how much power monitor retreats, and is usually referred to as "Light" in the display screen of your monitor. Adjust the volume of the monitor affects the amount of light emitted by its light. In our tests, we found that trumps every other light setting for energy saving; monitors had the same amount of energy whether we were watching a game or Blu-ray movies, while the light setting is consistent.
You may be wondering how contrast fits all. Truth is not. Because the contrast setting controls only the white level and the monitor has nothing to do with lighting, not to have an effect on energy consumption.


If your monitor has a switch, use
Most LCD monitors are not turned completely off when you press the button and still draw some amount of energy. To ensure your monitor is not drawing power, click off the switch - usually found on the underside of your desk, near its connection options - if you have. Switch acts as an extra degree of power conservation. If the switch is, the monitor can be turned by pressing the button, but if you turned off the monitor can be turned in - even by the key - unless the switch is turned back.
If you're going to be away from your computer for a day or more and your monitor has no switch, unplug from the wall to make sure it is not sucking power.

 
Upgrade from CRT to LCD
If you're still using a CRT monitor, consider finally taking the plunge LCD screen. Not only will you save money and consume less power, but will also have more space on your desktop mouse pads, keyboards, and a little plush dolls, if you're in that sort of thing.
We tested the Sony GDM520K 20-inch CRT via VGA and based on our test methodology (see the test LCD monitor energy consumption) of the annual cost of CRT is 63 percent higher than the 20-inch widescreen HP 2009m.
Upgrade of Cold Cathode Fluorescent Lamp (CCFL) to light-emitting diode (LED)
CCFL and LED related to the types of lighting in the LCD monitor. Most monitors use CCFL backlighting, not so effective in filling the screen with light from the LED backlight. CCFL backlight, consists of several tubes arranged horizontally across the rear panel monitor. With LED lights, there are many individual LED diodes around the back of each screen that can not be excluded either. This gives very precise LED displays on the control amount of light coming through the screen, and therefore more efficient in energy consumption. LED-based LCDs also have the potential to perform better than CCFL monitors color accuracy and can be produced with much thinner slabs based CCFL screen.
We tested three LED LCD monitors, Dell G2210, Dell G2410 and ViewSonic VLED22. In our tests, Dell G2210 and G2410 LED really lived up to the hype, earning all our energy saving seal. The ViewSonic VLED22, not so much. The ViewSonic does not bad, just not to our energy saving standards (see the test LCD monitor energy consumption).


Take a smaller monitor
We know, playing Crysis on your 30-inch Dell in 2560 X1 ,600-pixel resolution is a reason to live, but it is also the reason for Energy company expect your monthly energy readings. The fewer pixels lighting should illuminate, the less power it uses. If you can stomach a smaller monitor, know that it will save you cash.


Panel Technology
Another factor that determines how much energy a monitor draws a type of panel it uses. In our tests, we found that the Twisted Nematic (TN) panels percenr pull 45 to 49 percent less juice super patterned vertical alignment (S-PVA) models with the same size. Obviously, IPS panels (which usually have better visual quality than TN panels) require more power for that extra pizzazz.

read more...

How To Boot Backtrack From CD/USB

How to boot backtrack from CD / USB
Follow the steps outlined below to make quitting bootable CD / USB
Things
1st The first thing we need is quitting ISO. You can download the latest version of backtrack Here
2nd Universal USB installation using the USB conversion. You can download it from here
3rd Power ISO used to extract the ISO files. You can download it from here
Making bootable CD quitting
1st First to install Power ISO to open it. Now open the ISO file check downloaded files before you open -----> -------->" check your destination ISO file "

2nd Now insert a blank CD / DVD in the burner. Now click the Burn button and follow the onscreen instructions once complected burning can use the CD to boot backtrack
Making USB bootable backtrack
1st Open Universal USB Installer-enabled. Select check out version, check out ISO file and USB
drive and click Create

2. Follow the on screen instructions .once completed you can boot Backtrack from Usb

read more...

How To Make USB Drive Bootable?

# 1. The first step is to open a command line and follow the procedures as shown below.
Win + R -> cmd
Set the path in the command line as C: WindowsSystem32>

    16 How to make a USB Drive Bootable

    #2. Then type “diskpart”, a new window will appear as follows.

    C:WindowsSystem32>diskpart

    24 How to make a USB Drive Bootable

    #3. Next, type “list disk” command to show the status about the disks i.e. it displays the number of disks available in system.

    1. If pen drive was inserted then it shows list disk as Disk 0 and Disk 1 as shown in figure.

    DISKPART>list disk

    3 How to make a USB Drive Bootable

    #4. So, after finishing this one we have to select our pen drive disk to make it bootable. For this one use the following command as shown

    DISKPART>select disk 1

    1. Because our pen drive disk is 1 (compare the sizes of the disks then you can make a note which disk is our pen drive).
    2. Next type “list disk” command to make sure that our drive is selected or not

    DISKPART>list disk

    Then it shows a star mark at left side to make sure that drive is selected.

    The procedure is as follows

    42 How to make a USB Drive Bootable

    #5. Next we have to clear our pen drive memory space and make it empty. The command is as follows

    DISKPART>clean

    1. Then a message is displayed as follows “DiskPart succeeded in cleaning the Disk”.
    2. Next type “create partition primary” to create a primary partition. The command is as follows

    DISKPART>create partition primary

    1. A message will display as “DiskPart succeeded in creating the specified partition”.
    2. Next type “select partition 1” to create a partition. The command is as follows

    DISKPART>select partition 1

    1. “Partition 1 is now the selected partition” message will display.
    2. Type “active” command to mark the current partition as active. The command is as shown below.

    DISKPART>active

    1. A message “DiskPart marked the current partition as active” will display.
    2. The working of the above commands is shown in the below screenshot as follows

    52 How to make a USB Drive Bootable

    # 6. Next we need to format that pen drive using the FAT32 file system. The command is as follows
    DiskPart> FS = FAT32 format
    Wait until the "100 percent done" message to display.
    A message "DiskPart successfully formatted the volume" will be displayed.
    The next type "assign" command assign drive letter or mount point of that drive. The command is as follows
    DiskPart> assign
    "DiskPart successfully assigned the letter or mount point" will display a message.

      6 How to make a USB Drive Bootable

      After completion of all these process, then type “exit” command to exit that DISKPART windows and come back to first window i.e. C:WindowsSystem32

      Finally we will completed to process for making a bootable usb drive by typing this last command in first window as shown below.

      7 How to make a USB Drive Bootable

      From the above figure we can make a note that

      L – Pen drive or USB drive

      J – Bootable DVD or we can mount a bootable O.S Image File (.ISO)

      The final command is as follows

      C:WindowsSystem32>xcopy J:*.* /s/e/f L:

      A message “868 File(s) Copied” will display.

      83 How to make a USB Drive Bootable

      91 How to make a USB Drive Bootable

      Finally we finished the procedure to make a bootable USB Flash Drive or Pen Drive.
      But to make it work you must do one more thing, or to change the boot settings.
      I feel born will explain in a simple manner.
      Restart your computer and boot into settings (press F2: F2 system contains mainly as a default button) then it will redirect to the "Boot Options" and select "Boot USB device I" and set it to "Enable", then press F10 to save changes and exit.

      read more...

      Thursday, August 4, 2011

      Make USB bootable disk of ubuntu in ubuntu

      It is very simple. Only in terminal type: sudo apt-get install USB-creator-GTK.
      Then running in a terminal type: USB-creator-GTK.
      It shows that the new window select a source image (ISO instaliraat. of Ubuntu) and select the USB drive where to install.
      Then just make a startup disk.

      read more...

      Create a bootable Mac OS X Lion USB Flash / Pen Drive

      Create a bootable Mac OS X Lion USB Flash / Pen Drive
      As a result of my post about making bootable Leo 10.7 install DVD, here's how to make bootable USB flash drive.
      You will need the following: -
      A Mac
      A copy of the lion Installer-App (available from the AppStore)
      A USB Flash Drive / Pen Drive with 4.2GB (approx) space
      ** Note ** Unfortunately, this does not appear to quite fit the 4GB pen drive, you may find otherwise, but for me as a Disk Utility and "not enough space error" above (eg, 8GB) should be good.
      1 - Go to the Applications folder and right click (or Control-click) the 'Install Mac OS X Lion "and select" Show package contents.

      2 - Go to Content> SharedSupport folder

      3 - Copy InstallESD.dmg to someplace (eg. your Desktop)

      4 - Open Utilities > Disk Utility.app and click on your USB drive in the left pane.  Then click 'Partition'.

      5 - Enter a name for the partition and make sure the format is set to 'Mac OS Extended (Journaled)'.

      6 - Click 'Options' and choose 'GUID Partition Table' as the partioning scheme.

      7 - Click OK, then Apply, you will then have to confirm and authenticate you want to go ahead.  This will erase all data on your Flash drive!

      8 - Now click the tab, return, select (or drag) a copy of InstallESD.dmg you made earlier in the "Source" box.
      9 - Pull your USB flash drive to "Destination" box and click Restore, again you may need to authenticate.

      10 - After several minutes of your USB drive will be ready to do ... How long really depends on the speed of your USB drive, but most have a faster read speed of write and you just need to write again.
      11 - To test your USB drive, or go to system prefrences> startup disk and select any, then hit restart, or just hold down the Option / Alt key while you restart your computer.

      12 - Enjoy some peace of mind!

      read more...

      Make USB pen drive as a bootable device

      If you can not boot from DVD / CD-ROM drive, but you can not boot using a USB device, like USB pen drive, the following alternative boot method is available:
      usb10To boot using a USB pen drive, use the dd command to copy diskboot.img image / images / directory of the DVD or CD-ROM-enabled. For example:
      dd if = diskboot.img of = / dev / sda
      Your BIOS-enabled must support booting from USB device for this boot method to work.

      read more...

      Wednesday, August 3, 2011

      How to Make/Create a Bootable USB Flash Disk Windows Vista Installer

      Step-by-step beginners guide to style how to make easy, not only for the geeks but for everyone.

      format2

      1st Format the USB stick as NTFS: Open Windows Explorer and right click the drive> select a format option
      2nd The file system combo box, select NTFS and click the Start button to begin.
      3rd Then, open the Command Prompt as administrator, type in Start Search, cmd> Press Ctrl + Shift + Enter
      or are ... "Access Denied" message after opening diskpart command.
      4th Setting the Active Partition USB (Diskpart.exe)
      A Command Prompt, type: Diskpart and press Enter
      b. Wait for some time and type: list volume and press Enter
      - The command will see all drives and partitions
      C. Find that volume for your portable USB drive, in my case 6, why type: select volume 6 and press Enter again

       

      selectandactive

      D. Type: active and press Enter
      DiskPart marked the current partition as active.
      To learn more about the commands, press? and enter key.
      Now complete the volume setting so active, type the command and press Enter Exit Again
      5th Create Boot sector (bootsect.exe)
      What is Bootsect? In Command Prompt, enter the following command to get acquainted with a tool: bootsect /?
      Syntax:
      bootsect {/ Help | / nt60 | / nt52} {SYS | All | <DriveLetter>:} [/ force]
      Boot sector restoration tool
      Bootsect.exe updates the master boot code for hard disk partitions to switch between BOOTMGR and NTLDR. You can use this tool to recover the boot sector of your computer.
      Run "bootsect / help" for detailed instructions for use.
      It is located in your Windows Vista installation directory called \ lifting
      1st To return to the guide ... First, find where your DVD drive is (Windows Vista Installer-enabled) and go to the boot directory, which in my case drive F:
      Next, type: bootsect (space) / nt60 (space) Flash Drive Letter
      C: \ Windows \ System32> f:
      F: \> CD boot
      F: \ Boot> bootsect / nt60 is:
      Target volumes will be updated with BOOTMGR compatible bootcode.
      G: (? \ \ \ Volume {e5e56f28-84e3-11dd-bd4b-00188bdb682d})
      Successfully updated NTFS filesystem bootcode.
      Bootcode was successfully updated on all targeted volumes.
      F: \ Boot>
      6th You now have successfully created a department Boot Vista installer ... Finally, open Windows Explorer> Go to Installer-enabled the Windows Vista DVD drive and copy these files and folders on USB stick:

      copyvistadvd

      1st Boot directory
      2nd sources directory
      3rd The files in the root directory (drive)
      That's it!
      Now you have a bootable USB stick Vista Installer-enabled ... BTW that rocks! (As Mr. David said ... However, I too!)
      It is very useful in fixing problems and problems of Windows Vista for example, unbootable, infected with a virus, very slow and much more.

      read more...

      Solution to fix the USB Drive not recognized problem

      USBs are certainly made ​​our lives simpler and practical. We like our connecting pen drives, flash drives and other external devices in USB ports, but there is a strange problem that sometimes occurs when you enter our USB drive into a USB port to get an error message saying: "USB drive is not recognized."

      The error message reads "One of the USB devices attached to this computer has malfunctioned, and Windows does not recognize it. To help solve this problem, click this message." If you open My Computer you will notice that even our drive is not detected.
      The first thing that comes to our mind is that we should try uninstalling and then reinstall the USB drivers, but here is a simple solution and no need to edit registry or try something in Device Manager.


      Solution of the problem:
      1st The solution is simply to "Turn off the computer and unplug it from power" (as it takes off today even after turning the system off, the motherboard continues to gain power).
      2nd Let the system remain off for about a minute.
      3rd Restart the system and wait for it to boot completely before you put the drive back again.
      It is this problem will occur again.

      read more...

      The usb is not recognized by your computer

      You need to copy some important data from your pen drive computer hard drive. You plug in the USB device and nothing happens or you get an error that says something like USB flash drive is not recognized. What do we do then?
      Flash drives need no introduction and almost everyone owns today for fast data transfer and data storage purpose. Flash drives are also known by other names such as jump drives, pen drives, thumb drives, USB sticks, and others. There can be times when these devices useful data can give some problems when you connect to a PC. The most common problem when a USB device is connected to a computer flash drive is not recognized error.
      When that kind of error before troubleshooting step that should take is to turn off the computer, remove the pen drive from the port and try again after sometime. The closure of the system and reboot again, the computer drivers Reload removable drive, pen drive and then can eventually start to work. If this basic step does not seem to work, can move to the next step.

      usb14Flash Drive not recognized - causes and solutions
      Computer virus
      Many times, computers may be infected with a virus, which is why it can work in some strange way. This may even affect the proper functioning of any USB device that is connected to the system. To prevent this problem, it is recommended to install a good antivirus software and periodically scan and clean your computer. Purchase of licensed and updated version that will not only prevent any infection from malware, Trojans, spyware and other computer viruses, but also scan to a USB storage device data as soon as it is connected to a computer.
      Device Driver Corrupted or not present
      There are also possibilities that the USB device driver may be corrupted, causing flash drive can not recognize. To troubleshoot this problem flash drive, you must first uninstall the driver and then reinstall it again. You can do a proper uninstall the driver from Device Manager, which can be accessed through the "My Computer" or "Control Panel". To install drivers back again, use the CD-ROM that came with the flash drive. In older operating systems, there are no such drivers are present in the computer. So a USB flash drive to be recognized, you will need to install drivers from CD driver first.
      No connection to port
      If you are trying to plug in flash drive USB port which is located in front of the cabinet processor can not work and can not even get any error. The reason is simply that the extension cables can be incorporated to provide connectivity on the front. In case you were previously using the front USB ports without any issues, and are now unrecognizable device error, extension cables may be to blame. You need to open the cabinet and check the problem on.
      If any of the steps above problems do not seem to work, then probably the flash drive itself is to blame. To make sure that the flash drive is operating properly, use another computer and check if it works fine. If you get an error similar to the flash drive is not recognized, shut down computer, remove the USB connection, and check after reboot. If still not working, then probably the USB device is faulty and should try another flash drive or USB device.

      read more...

      Tuesday, August 2, 2011

      Get Help from us to solve your problems with Flash Drives

      USB Flash Drive not work on Macintosh
      Follow these steps if your USB Flash / Pen Drive not recognized or mount on Mac
      Scenario 1:
      If the light blinks and the drive stays or goes out, and they show signs of multiple computers, then the maximum chances are that the device is faulty and should be replaced (if under warranty) or time to get a new one!
      Scenario 2:
      If the device is used for the first time, verify the computer's operating system to ensure that the device is compatible. Also, if the drive device includes a center or in your USB keyboard, plug it directly into a USB port on the computer. If it works there, the question is the device that was previously connected. The device can put more power than the port provides.
      Scenario 3:

      If the device is used for work, and now his work and the light comes on then there is a strong possibility that we can still fix this drive. Follow these steps:
      * Step 1: Turn on the device MAC and are waiting for any signs of recognition, if not get anything Jump to step 2.
      * Step 2: Check System Profiler to find if the disk is recognized at all or not. (System Profiler as the Device Manager in Windows) Click the Apple and click on About this Mac.
      This tells you the version of MAC, as 10.5.2 and the opportunity for more information
      Step 3: If the MAC version is supported by the device click on more information, select USB on the left panel and look for the device to the USB device tree on the right.
      If the device does not appear in System Profiler

      usb9The question is more likely to be a hardware problem. Test if the flash drive does not work on other computers and if it does not work on another computer seems to be the USB port is not functioning properly.
      If the device appears in System Profiler
      Even if the device does not work, the issue is usually due to software. Jump to the next step
      * Step 4 - Check Disk Utility
      To the desktop, open the hard drive> Applications> Utilities> Disk Utility.
      Type / space / the path and click Go
      Make sure you keep the capital V.
      - You'll find the window size
      - Highlight the name of your device if it shows mounted at the top, click on the mountain, so that changes to Unmount
      - If the device now appears on the desktop if you are still not there, then follow the following steps
      . Click the Go menu on the desktop and click the Go to Folder
      Look for a flash drive in the window if it is present there, click on it to make sure that you can view your data
      If you are able to view your data are good to go, you can drag and drop the volume of the work here and will appear there as well
      - If the device fails to appear in the volume menu from there you be the best solution is to try updating drivers or create a new user.

      read more...

      PSP - USB Device Not Recognized

      PSP - USB Device Not Recognized
      I tried to connect my PSP to my computer, but when I connected the USB to PSP error message appears on the taskbar stating: ". One of the devices attached to this computer has malfunctioned, and Windows does not recognize "And when I clicked on the message as specified window appears titled USB device not recognized and the location of the" unknown device "was listed, but not using the unused USB port. This puzzles me. How come my computer does not recognize the unit PSP? I tried plugging in my USB flash drive and was running well.
      usb4Her birthday is my little brother that I bought one month in advance to try it myself because I want to work correctly before you give it. I need a fix faster than his bday is fast approaching, I feel cheated. I tried Googling, dived into some forums and saw many similar problems but no real solution.
      Some said to reformat the Memory Stick, some suggest to plug in different USB port or try it on another computer, some told me to uninstall the USB drivers Device Manager and reboot to install Windows ... But none of those things for me, then come to a conclusion that may be defective USB cable so I bought a new cable and Voila! I got the job .. I never thought that the problem is the USB cable because it was day before.

      read more...

      Flash Drive Not Recognized?

      Flash Drive not recognized?
      Seeing the flash drive is not recognized error pop-up on your computer is both good and bad news.
      The bad news is obvious, your jump drive not working, which means that if qoute lies in your computer, flash drive, or it was a fluky one-time incident. The good news is that this situation is fairly easy to fix and most of the time it will not cost you money.
      Flash Drive

      usb7This message can occur hundreds of different reasons, literally. One of the main problems is that people often ignore the "safely remove hardware" option when they remove their flash drive from their computer. Often data is downloaded it gets corrupted and may damage the jump drive together.
      Less favorite reasons why this message appears containing a broken jump drive or a computer running the operating law that is out of date.
      The best way to fix this qoute is simply try again. Take your flash drive to break 10 seconds and try again. There is a minute job and no risk here, so it does not hurt to at least try. If it does not work, try restarting your computer, at least half of all computer problems can be solved by simple restart.


      This qoute seems aimed Windows based computers and laptops primarily, but Mac, and even the PS3 and Xbox 360 are known to spit this error message. Make sure you cool and assume that your jump drive is broken.
      Flash Drive not recognized?

      read more...

      Why Flash Drive Not Detected Computer??

      Flash Drive not detected Computer
      Some things should be suspected when the UFD (USB flash drive) that are not detected when the camera into the computer, among others:
      - Damaged USB Port
      - Setting up the problem (bios, Windows)
      - Driver problems
      - Damaged by natural
      - Others

      usb4
      Why Flash Drive Detected Computer
      To try to overcome it can make the following points: Try our USB plug in another USB port / switch-move, if they failed to try to plug in another computer, if successful, then we are not problematic USB and doubt 100% of the computer.
      Or the opposite, try another USB port on your computer (if any) / or other devices that use USB ports. By assumption, if the tools we connect is detected, the USB ports are not problematic.


      Check the BIOS settings can turn off intentionally or not, it could happen does not change the settings with the motherboard battery when we realize we are worn / weak.
      Check in Device Manager, follow these steps:
      1st Click Start> Settings> Control Panels.
      2nd Double-click the System icon
      3rd Once open window Syistem Properties, click the Hardware tab
      4th Click the Device Manager button
      5th Then check out the Universal Serial Bus controllers, it seems that there is a problem
      6th Question in this section indicates the hardware is not recognized or td driver
      7th Red Cross marks in this section shows disabled, so if it happens right click and select enable
      8th Included in this is likely to re-install the USB flash disk driver.


      Check register, including:
      1st Click Start> Run
      2nd Type: regedit then enter usb5
      3rd Go to: HKEY_LOCAL_MACHINE \ SYSTEM \ CurrentControlSet \ Services \ UsbStor
      4th Value Dwords be worth 3 (enable) if not 3, then update with 3, then close and restart
      Another possibility is a computer infected with a virus, it must be free of the virus using anti-virus
      If you suspect that the new software is installed as the cause then try to uninstall the software first.
      Try to use software tool to find and mount the partition (hopefully you).

      read more...

      Monday, August 1, 2011

      How to fix USB not recognized

      How to fix USB not recognized

      If you insert the USB and it is not recognized in Windows, there are several things you can try to get it to show up in My Computer. Thumb drives or flash drives, USB devices are to be automatically recognized by Windows when you enter. There can be no conflicts or partition issues prevent it from appearing or used for storage. Follow these steps to troubleshoot the USB is not recognized on your computer.

      Remove thumb drives
      If you insert your USB and nothing happens, follow these steps to try and fix the problem:
      * Go to Start and right click on My Computer (or Computer) and select Manage. Under Disk Management, locate your thumb drive, right click and select change drive letter. If you already have a letter, try a different award, as may be trying to use a letter that's already assigned to another device.

      * If it does not work, try restarting the computer with the USB adds the USB port and see if that helps.
      * Try other USB ports, or try off other USB devices that can interfere with it.
      * Under disk management again reiterated USB is partitioned and formatted. If not, right-click the hard drive and proceed to format. Note: All data will be deleted from disk.
      To prevent accidental damage to your thumb drive, do not forget to remove it from your computer properly after each use. If the external drive is connected to your computer, you can see the Safely Remove Hardware icon in the system try your watch. Before removing the USB thumb drive, click on that icon and find your drive in the list and select "Remove." It will display a message stating when the device is stopped. You can also open My Computer and right-click the hard drive and then select "Eject."

      Thumb drives are very fragile and unreliable. It may be possible it has completely failed. Be sure to use thumb drives only as temporary storage, and also try and backup all data stored on removable disks.

      read more...

      What can you do to prevent corruption USB?

      What can you do to prevent corruption USB?
      If you insert a flash drive in Windows XP, normally recognizes the flash drive and immediately sets the flash drive for use as a regular storage device. When you need to disconnect the flash drive, use the "Safely Remove Hardware" icon and tell Windows that you want to remove the flash drive. Then, Windows will write any data waiting (Windows XP uses a delayed-write cache to speed up programs), and then says that drive is not connected. Finally, it tells you that the flash drive can now be removed. But if you just pull the flash drive without doing Safely Remove Hardware step, you may lose data that you thought was already written on the flash drive.

      usb3Also, Windows will not properly turn off its internal settings for the drive. This means that if you insert the drive again Windows XP will not recognize. You must reboot your computer to restore the flash drive recognition.
      Instead of using the Windows option, I personally prefer a free portable utilities EjectUSB, who will perform all the flash drive close to me.

      read more...

      How to set a fresh partition to USB Drive?

      If the USB device has a permanent failure recognition, and data on disk is not essential for you might just try creating a new partition. Definitely, if the device is hardware problems that would be useful. Follow the instructions:

      usb2
      * Go to the Start menu, then click the Run option.
      * Now type "diskmgmt.msc" command, then hit the Enter key.
      * Locate the USB at the bottom of the window that opens, and right click on it.
      * Now delete the partition on the USB.
      * Create a new partition, right-click the USB option. Format in FAT or FAT32 format.
      * Remove the USB and reinsert it into the computer.

      read more...

      Thumb Drive not Recognized in Windows XP

      You can attach a USB based device with a computer that runs on Windows XP. Then, you try to scan for hardware devices. However, the computer detects a device attached, and you do not see the device in My Computer folder. Does the problem look familiar to you? Well, it happens once a while with everyone.
      Image and video hosting by network

      usb1

      To fix this issue, I would recommend the following action plan:
      1st First, we patiently waited a little to ensure that the problem is not related to your computer is busy and dealing with other things.
      2nd If you include this device into a USB hub, it could point to the center failure to perform due to power failure or just outside. Try to switch the device directly into a USB port on the front, or if it does not help, in the back of your computer.
      3rd Restart the computer and try again to join back.
      4th Check performance USB drive to another computer and see if the problem connected with the drive itself.
      5th If the USB device works fine on another computer, you can return to your original computer problems.
      6th Go to Start-> Settings-> Control Panel-> Administrative Tools-> Disk Management to drive in the computer and see if the letter is connected with USB. If not, assign a drive letter.
      7th Access Device Manager and check whether you see any signs of your drive there. Keep in mind that depending on the configuration computer, your USB drive can appear in different sections, such as disk, DVD / CD-ROM devices, or Universal Serial Bus controls as USB Mass Storage. If not see if the yellow question mark, delete. Then, scan for software changes and see if the drive will appear as a healthy element of the configuration.
      8th Access Device Manager and remove all items related to USB such as USB root hub, etc, reboot the computer twice to let Windows install properly, then try the flash drive again.
      9th Next step is the registry change related, so you should be careful making any changes.

      The best way is to play safe, and making a backup registry (registry by exporting the registry patch) before making any changes.
      1st Get in the Registry Editor - Press Start -> Run, type regedit in the window, and press OK.
      2nd Click on my computer. Then press File Export, assign easily recognizable file name to backup the registry.
      3rd Navigate to the following registry key HKEY_LOCAL_MACHINE / System / CurrentControlSet / Control / StorageDevicePolicies.
      4th In the right panel select "writeprotect".
      5th Reset the value to '0 '.
      6th Repeat for the registry key ControlSet001 and ControlSet002, if they exist.
      7th Now plug your USB drives and should work. Else just reboot the machine to try.
      10th The last step is also associated with registry changes, and recommended by the Microsoft Knowledge Base, the deletng UpperFilters registry value and LowerFilters registry value. To do this, follow these steps:
      1st Click Start, click Run, type regedit, and then click OK.
      2nd Locate and then click UpperFilters registry value. This value is in the following registry subkey: HKEY_LOCAL_MACHINE \ SYSTEM \ CurrentControlSet \ Control \ Class \ {4D36E967-E325-11CE-BFC1-08002BE10318}
      3rd The menu Edit, click Delete, and then click OK.
      Note If you receive an error when you try to delete the registry subkey may not have appropriate permissions to edit the subkey.
      4th Locate and then click LowerFilters registry value. This value is in the following registry subkey: HKEY_LOCAL_MACHINE \ SYSTEM \ CurrentControlSet \ Control \ Class \ {4D36E967-E325-11CE-BFC1-08002BE10318}
      5th The menu Edit, click Delete, and then click OK.
      Note If you receive an error when you try to delete the registry subkey may not have appropriate permissions to edit the subkey.
      6th Exit Registry Editor.
      7th Restart the computer.

      read more...

      Saturday, July 9, 2011

      Make Your Work Hours at the Computer More Comfortable

      Dr Yip Treat Fracture & Dislocation In Elbow Sprain, Swollen And Pain

      Erg-Smart Workstation tutorial
      The Office Ergonomics presentation is a much watch for anyone who spends a fair amount of time infront of the desktop computer. [related: Rearrange Your Workspace]
      This quick and interactive presentation will help you identify potential risks for pain and strain in your current office environment.
      Then there are some easy-to-implement suggestions to help setup your desktop workstation and modify your work practices to minimize ergonomic risks. For instance,
      » The top edge of the monitor should be at or below your eye-level.
      » You can place a phone book under the computer monitor to raise the level.
      These little adjustments can make your work hours at the workstation much more comfortable.

      read more...

      Tips for caring eyes in front of computer

      Studies have found that the majority of people who work at a computer experience some eye or vision problems, and that the level of discomfort appears to increase with the amount of computer use.

      But, increased use of smaller, portable work and recreational gadgets such as Personal Digital Assistants, laptops and cell phones used for text messaging and Web access may also be contributing factors to the visual fatigue and discomfort experienced by millions, according to a leading expert.

      "The unique characteristics and high visual demands of computer work and play make many individuals susceptible to the development of eye and vision-related problems," notes Dr. Jeffrey Anshel, a practicing optometrist and author of Visual Ergonomics in the Workplace. "With the proliferation of portable electronic devices such as laptops, palm pilots and video game players, it's no surprise that eye care professionals are seeing more patients who complain of ocular discomfort."

      Indeed, a national survey of doctors of optometry found that more than 14 percent of their patients present with eye or vision-related symptoms resulting from computer work. Furthermore, in a survey of more than 2,000 current and former contact lens wearers, time spent in front of a computer (41 percent) was the activity most frequently mentioned as causing discomfort while they were wearing their lenses.

      Staring at a computer monitor or the small screens on most devices can lead to a variety of ailments, including headaches, eyestrain, blurred vision, dry and irritated eyes, neck and/or backache and sensitivity to light.

      "Eye stress and strain may be caused by a combination of individual visual problems, improper viewing habits and poor environmental conditions, such as glare, improper workstation set up, dirty screens, poor lighting and viewing angles," explains Dr. Anshel, who has helped companies and government agencies, including Mitsubishi, American Airlines, 3M and the Department of Labor address the high stress area of vision demands in relation to working with computer monitors.

      "Uncorrected or under-corrected vision problems can be major contributing factors to computer related eye stress, affecting visual performance and comfort," cautions Dr. Anshel.

      "The good news is that many potential eye and/or vision problems can be reduced or eliminated by appropriate adjustment and placement of computer monitors, lighting control, good preventive vision care habits and regular professional eye care." Dr. Anshel offers the following advice to help prevent or reduce the development of vision-related problems.

      For additional tips, take the "Eye Q's and Views" interactive quiz at http://www.computerquiz.jnjvision.com.

      -- REDUCE GLARE - Extraneous light, or glare, is the greatest source of eyestrain for computer users. No matter where your computer is relative to a window, adjustable shades, curtains or blinds should be used to effectively control light levels throughout the day. Avoid facing an un-shaded window since the difference in brightness between the screen and the area behind it may be cause eye stress and discomfort. Consider using an anti-glare screen to reduce reflections.

      -- CHECK YOUR CONTACTS - When working at a computer, people spend a lot of time concentrating and blink less frequently - about three times less than normally, according to studies. "Computer work is particularly stressful for contact lens wearers," says Dr. Anshel. "Long non-blinking phases may cause the surface of contact lenses to dry out, which can lead to discomfort and a loss of visual clarity." He recommends talking to an eye care professional about ACUVUE® OASYS™ with HYDRACLEAR™ Plus. In a clinical study with 335 contact lens wearers, nine in 10 (89 percent) patients wearing ACUVUE® OASYS™ said that their eyes felt comfortable, even when watching TV or using a computer for a long time.

      -- ADJUST YOUR MONITOR - Ideal monitor placement is dependent on several factors including an individual's physical make-up and visual capabilities, work tasks and other workstation design elements. For maximum eye comfort, Dr. Anshel recommends placing the center of the screen five to nine inches below your horizontal line of sight. "You should be looking just over the top of the monitor in your straight-ahead gaze," he says.

      -- TAKE A BREAK - "Our eyes were not made to see at a close distance for hours at a time without a break," says Dr. Anshel. A preventive approach to reducing visual stress includes occasionally looking away from the screen of your computer, PDA or portable game player. Dr. Anshel recommends the 20/20/20 rule. "Take a 20-second break every 20 minutes. Focus your eyes on points at least 20 feet from your terminal. Keep your eyes moving while looking at objects at various distances," he says.
      -- CONSULT YOUR EYE CARE PROFESSIONAL - The American Optometric Association highly suggests yearly eye exams to ensure ocular health. For individuals whose jobs may require extensive time in front of a monitor, Dr. Anshel suggests a comprehensive eye examination soon after beginning computer work and periodically thereafter. "If, at any time, you experience any vision problems or discomfort, talk to your eye care professional," he adds.

      read more...

      Saturday, July 2, 2011

      10 Cool things you can do with your USB Flash Drives

      By Greg Shultz

      Transporting your data is probably the most common use for a USB flash drive. But there’s a world of other things you can do with these handy pocket-size drives. Here are 10 ways you can use that USB flash drive to do more than just move data.

      1: Run portable applications

      In addition to storing your data, you can run portable applications from a USB flash drive. For example, OpenOffice, which is a complete office suite that includes a word processor, spreadsheet, presentation tool, drawing package, and database, is available as a portable application. Mozilla Firefox and Thunderbird are also available as portable applications. When you combine the office suite with the ability to surf the Web and check email, you’ll be able to take your most vital computing applications with you wherever you go — right in your pocket.

      If that’s not enough, you can choose other applications to install on your USB flash drive from PortableApps.com (Figure A). You can even install an entire prepackaged suite of applications that includes such things as an audio player, games, an antivirus utility, and a handy menu system.

      Figure A

      2: Boot an operating system

      If you want to do more than just run your own applications, you might want to consider booting an entire operating system from your USB flash drive. You can boot either Windows or Linux from a USB flash drive; however, the process is not an exact science and you may be in for a technical adventure.

      Fortunately, there are some guides you can follow. To learn how to boot Windows XP from a USB flash drive, see the article Creating a bootable USB flash drive for Windows XP. To learn how to boot a version of Linux from a USB flash drive, see the article Puppy Linux teaches an old dog new tricks.

      3: Connect to a wireless network

      If you have a wireless network, you can use the Wireless Network Setup Wizard in Windows XP or the Windows Connect Now (WCN) feature built into Vista to save wireless network configuration information to a USB flash drive. You can then use your drive to quickly and easily connect another computer or a WCN-compatible device, such as a router or printer, to your wireless network. To learn more about using the Wireless Network Setup Wizard, see the Help And Support Center, which is accessible from Windows XP’s Start menu. To learn more about using the Windows Connect Now feature, see Windows Help And Support, which is accessible from Windows Vista’s Start menu.

      4: Create a password reset disk

      A password reset disk can really come in handy if you forget the password to your user account on a Windows system that is not a part of a domain. If you find yourself in that situation, you can use the password reset disk to reset your password and quickly get back into your user account. In Windows Vista, you can use USB flash drive rather than a floppy disk as a password reset disk (Figure B). For details on how to do so, see the article Create a Vista password reset disk using a USB flash drive.

      Figure B

      You can use your USB flash drive as a password reset disk.
      5: Boost performance

      If you’re running Windows Vista, you can use a USB flash drive to speed up your system with the ReadyBoost technology. ReadyBoost can use the storage space on a USB Flash drive as an additional memory cache to aid the memory cache on your hard disk. And because flash memory is more responsive than a hard disk, with its physical moving parts, the memory cache provided by ReadyBoost can significantly improve system responsiveness.

      Using ReadyBoost is easy. You just insert your USB flash drive into your Vista system and follow the onscreen prompts to configure and use ReadyBoost. If you want more details, check out the article How SuperFetch and ReadyBoost work together.

      6: Manage it

      If all you really want to do with your USB flash drive is transport data, and you’re running Windows XP, you can do so more efficiently with the Microsoft USB Flash Drive Manager (Figure C). Once you have installed this manager, you can easily copy files to and from your drive, back up and restore the entire flash drive to and from your hard disk, change the drive label, and even create an autorun.inf file to launch Drive Manager automatically when you plug in the drive. To learn more about and download the USB Flash Drive Manager visit the Microsoft TechNet Magazine site.

      Figure C

      The Microsoft USB Flash Drive Manager provides you with a host of features, such as drive backup.
      7: Use it as an MP3 player

      Would you like to be listening to music when you’re using a computer at the office, but you don’t have an MP3 player? If so, you can use a USB flash drive as an MP3 player along with Windows Media Player and a set of headphones. Just copy your MP3 files to your USB flash drive, plug it into your computer, and direct Windows Media Player to build a library of the songs on your drive. You can use all of Windows Media Player’s playback features, such as playlists and favorites, to easily customize your music listening experience. And best of all, you won’t have to worry about running low on battery power.

      8: Password-protect it

      If you use a USB flash drive to transport sensitive data that you would prefer to protect from prying eyes, should you lose the drive, Rohos Mini Drive (Figure D) can safeguard that data. This security tool allows you to create a secret partition on the drive and then password-protect/encrypt that partition, thus protecting any documents you copy to that partition via the utility’s file manager. You can download (and read a review of) Rohos Mini Drive at Download.com.

      Figure D

      Using Rohos Mini Drive, you can secure sensitive files on your USB flash drive.
      9: Run a Web site from it

      If you are a Web developer, you may be interested to know that with Server2Go, you can easily run a Web server that supports Apache, PHP, MySQL, and Perl right from a USB flash drive. You can use Server2Go right out of the box without any installation. It runs on all versions of Windows, supports most common browsers, and is completely free. To a developer, the benefits of having a portable Web server on a USB drive are numerous. For example, imagine being able to carry a live Web site demo into a sales pitch meeting. For more information about this package, visit the Server2Go site.

      10: Lock your PC

      Have you ever seen a movie in which a person in some secret government installation simply inserts and removes a card to log in and log out of a PC? If you thought that idea was cool, you’ll definitely want to investigate Predator (Figure E). Once installed and configured, this little freeware utility will allow you to turn a USB flash drive into a key you can use to lock and unlock your computer.

      Figure E

      With Predator, you can use a USB flash drive as a key to lock and unlock your computer.

      While the USB flash drive is connected to your computer, everything works as it normally would. Once you remove the USB flash drive, your computer is locked down — the keyboard and mouse are disabled and the screen darkens. To unlock your computer, you just plug in the USB flash drive and the computer will be unlocked and you can begin using it. To learn more about Predator, and/or to download it, visit the developer’s Web site.

      http://amarpr33t.wordpress.com/2011/05/19/10-cool-things-you-can-do-with-a-usb-flash-drive/

      read more...